powerpc/pseries/hvconsole: Fix stack overread via udbg

While developing KASAN for 64-bit book3s, I hit the following stack
over-read.

It occurs because the hypercall to put characters onto the terminal
takes 2 longs (128 bits/16 bytes) of characters at a time, and so
hvc_put_chars() would unconditionally copy 16 bytes from the argument
buffer, regardless of supplied length. However, udbg_hvc_putc() can
call hvc_put_chars() with a single-byte buffer, leading to the error.

  ==================================================================
  BUG: KASAN: stack-out-of-bounds in hvc_put_chars+0xdc/0x110
  Read of size 8 at addr c0000000023e7a90 by task swapper/0

  CPU: 0 PID: 0 Comm: swapper Not tainted 5.2.0-rc2-next-20190528-02824-g048a6ab4835b torvalds#113
  Call Trace:
    dump_stack+0x104/0x154 (unreliable)
    print_address_description+0xa0/0x30c
    __kasan_report+0x20c/0x224
    kasan_report+0x18/0x30
    __asan_report_load8_noabort+0x24/0x40
    hvc_put_chars+0xdc/0x110
    hvterm_raw_put_chars+0x9c/0x110
    udbg_hvc_putc+0x154/0x200
    udbg_write+0xf0/0x240
    console_unlock+0x868/0xd30
    register_console+0x970/0xe90
    register_early_udbg_console+0xf8/0x114
    setup_arch+0x108/0x790
    start_kernel+0x104/0x784
    start_here_common+0x1c/0x534

  Memory state around the buggy address:
   c0000000023e7980: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
   c0000000023e7a00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1
  >c0000000023e7a80: f1 f1 01 f2 f2 f2 00 00 00 00 00 00 00 00 00 00
                           ^
   c0000000023e7b00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
   c0000000023e7b80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  ==================================================================

Document that a 16-byte buffer is requred, and provide it in udbg.

Signed-off-by: Daniel Axtens <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>

arch/powerpc/platforms/pseries/hvconsole.c

@@ -62,7 +62,7 @@ EXPORT_SYMBOL(hvc_get_chars);
  * @vtermno: The vtermno or unit_address of the adapter from which the data
  *	originated.
  * @buf: The character buffer that contains the character data to send to
- *	firmware.
+ *	firmware. Must be at least 16 bytes, even if count is less than 16.
  * @count: Send this number of characters.
  */
 int hvc_put_chars(uint32_t vtermno, const char *buf, int count)

drivers/tty/hvc/hvc_vio.c

@@ -107,6 +107,14 @@ static int hvterm_raw_get_chars(uint32_t vtermno, char *buf, int count)
 	return got;
 }
 
+/**
+ * hvterm_raw_put_chars: send characters to firmware for given vterm adapter
+ * @vtermno: The virtual terminal number.
+ * @buf: The characters to send. Because of the underlying hypercall in
+ *       hvc_put_chars(), this buffer must be at least 16 bytes long, even if
+ *       you are sending fewer chars.
+ * @count: number of chars to send.
+ */
 static int hvterm_raw_put_chars(uint32_t vtermno, const char *buf, int count)
 {
 	struct hvterm_priv *pv = hvterm_privs[vtermno];
@@ -219,6 +227,7 @@ static const struct hv_ops hvterm_hvsi_ops = {
 static void udbg_hvc_putc(char c)
 {
 	int count = -1;
+	unsigned char bounce_buffer[16];
 
 	if (!hvterm_privs[0])
 		return;
@@ -229,7 +238,12 @@ static void udbg_hvc_putc(char c)
 	do {
 		switch(hvterm_privs[0]->proto) {
 		case HV_PROTOCOL_RAW:
-			count = hvterm_raw_put_chars(0, &c, 1);
+			/*
+			 * hvterm_raw_put_chars requires at least a 16-byte
+			 * buffer, so go via the bounce buffer
+			 */
+			bounce_buffer[0] = c;
+			count = hvterm_raw_put_chars(0, bounce_buffer, 1);
 			break;
 		case HV_PROTOCOL_HVSI:
 			count = hvterm_hvsi_put_chars(0, &c, 1);