Claudio is a wake up alarm based on ESP32 by Espressif Systems and programmed with Arduino IDE
Folders:
/ Arduino IDE code
/box Prototype print 3d files
/hardware Hardware pictures
More info and demos at: https://www.youtube.com/watch?v=NURag-YYxIY
By default, Claudio is listening on port 1234 for incoming connections.
These connections allow a remote system to configure or perform some actions on the system. (Change parameters, Set alarm time, Deactivate alarm, ...)
Once the remote client is connected to claudio, commands are sent concatenated to items and values all in upper case.
For instance, if we want to know the number of beeps to sound during an alarm, we must use the command GET followed by the item ALBEEP:
GETALBEEPIf all succeed, the system will reply
90which is the value cofigured for this parameter. Otherwise, the system could reply "Invalid Command" or "Invalid Item"
If we want to change the value of this parameter, for instance to 120, we should send
SETALBEEP120and the system should reply
OKGET Retrieves the value of the specified item.
SET Stores the specified value in the specified item.
GET Retrieves all the items value in a concatenated string ITEM1 + VALUE1 + ; + ... + ITEMn + VALUEn + ;
For instance:
BOOTWT5;TOUCHR120;THTCHR70;THTCHM65;THTCHL65;LTCHTH12;...RST Reboot the system.
TSS Stops and deactivates alarm, even while alarm is being executed.
BOOTWT
Number of seconds (aprox.) to wait after boot screen to start the normal operation
EEPROM stored: Yes
Default value: 20
TOUCHR
Number of readings to calculate sensor capacitance average value
EEPROM stored: Yes
Default value: 120
THTCHR
Average capacitance threshold value for Right sensor. Under this value the sensor is considered activated
EEPROM stored: Yes
Default value: 70
THTCHM
Average capacitance threshold value for Middle sensor. Under this value the sensor is considered activated
EEPROM stored: Yes
Default value: 65
THTCHL
Average capacitance threshold value for Left sensor. Under this value the sensor is considered activated
EEPROM stored: Yes
Default value: 65
LTCHTH
Long touch threshold. Number of tenths of a second to consider a sensor has been long touched.
EEPROM stored: Yes
Default value: 12 (1.2 secs)
SNZMIN
Number of minutes to postpone alarm time (Snooze)
EEPROM stored: Yes
Default value: 9
ALBEEP
Number of beeps to sound during alarm
EEPROM stored: Yes
Default value: 90
MAXLUX
Maximum lux value to take into account. Above this any value is just considered maximum value.
When ambient light reaches this value, the display backlight is set to 100% power.
EEPROM stored: Yes
Default value: 20
MINLUX
Minimum lux value to take into account. Below this any value is just considered minimum value.
When ambient light goes down to this value, the display backlight is set to Minimun Brightness value. (see next item))
EEPROM stored: Yes
Default value: 0
MINBRG
When ambient light reaches its minimum value, display backlight power is set to this value.
This is commonly used to set the backlight level we want while sleeping.
EEPROM stored: Yes
Default value: 10
ALARHO
Defines the hour part of alarm time
EEPROM stored: No
Default value: No default value
ALARMI
Defines the minutes part of alarm time
EEPROM stored: No
Default value: No default value
DOALAR
Switch ON/OFF alarm by sending 1/0 value for this item
EEPROM stored: No
Default value: No default value
ONALAR
Indicates whether the alarm is beeping or not. As well, it stops alarm beeping if its value is set to 0
EEPROM stored: No
Default value: No default value
To test remote configuration capabilities you can use Claudio Remote, an Android app to change configuration values easily: https://github.com/pangodream/ClaudioRemote