PrusaSlicer-2.2.0-beta

This release mirrors PrusaSlicer's upstream 2.2.0-beta.

To use this AppImage, dependencies on the host might be needed (Raspbian Buster):

sudo apt install -y git cmake libboost-dev libboost-regex-dev libboost-filesystem-dev \
libboost-thread-dev libboost-log-dev libboost-locale-dev libcurl4-openssl-dev \
libwxgtk3.0-dev build-essential pkg-config libtbb-dev zlib1g-dev libcereal-dev \
libeigen3-dev libnlopt-cxx-dev libudev-dev \
libopenvdb-dev libboost-iostreams-dev \
libnlopt-dev

After installation, chmod +x PrusaSlicer-2.2.0-beta-armhf.AppImage and run it.

New: This release was built using an additional, external deb package. In the event of problems, it may also need to be installed locally http://raspbian.raspberrypi.org/raspbian/pool/main/c/cgal/libcgal-dev_5.0.1-1_armhf.deb.

PrusaSlicer 2.2.0-alpha4-armhf

This release mirrors PrusaSlicer's upstream 2.2.0-alpha4.

To use this AppImage, dependencies on the host are needed (Raspbian Buster):

sudo apt install -y git cmake libboost-dev libboost-regex-dev libboost-filesystem-dev \
libboost-thread-dev libboost-log-dev libboost-locale-dev libcurl4-openssl-dev \
libwxgtk3.0-dev build-essential pkg-config libtbb-dev zlib1g-dev libcereal-dev \
libeigen3-dev libnlopt-cxx-dev libudev-dev \
libopenvdb-dev libboost-iostreams-dev \
libnlopt-dev

After installation, chmod +x PrusaSlicer-2.2.0-alpha4-armhf.AppImage and run it.

New: This release was built using an additional, external deb package. In the event of problems, it may also need to be installed locally http://raspbian.raspberrypi.org/raspbian/pool/main/c/cgal/libcgal-dev_5.0.1-1_armhf.deb.

PrusaSlicer 2.2.0-alpha3-armhf

This release mirrors PrusaSlicer's upstream 2.2.0-alpha3.

To use this AppImage, dependencies on the host are needed (Raspbian Buster):

apt install -y git cmake libboost-dev libboost-regex-dev libboost-filesystem-dev libboost-thread-dev libboost-log-dev libboost-locale-dev libcurl4-openssl-dev libwxgtk3.0-dev build-essential pkg-config libtbb-dev zlib1g-dev libcereal-dev libeigen3-dev libnlopt-cxx-dev libudev-dev

After installation, chmod +x PrusaSlicer-2.2.0-alpha3-armhf.AppImage and run it.

PrusaSlicer 2.2.0-alpha2-armhf

This release mirrors PrusaSlicer's upstream 2.2.0-alpha2.

To use this AppImage, dependencies on the host are needed (Raspbian Buster):

apt install -y libboost-dev libboost-regex-dev libboost-filesystem-dev \
libboost-thread-dev libboost-log-dev libboost-locale-dev libcurl4-openssl-dev \
libwxgtk3.0-dev libtbb-dev libcereal-dev libeigen3-dev libnlopt-cxx-dev libudev-dev

After installation, chmod +x PrusaSlicer-2.2.0-alpha2-armhf.AppImage and run it.

PrusaSlicer 2.2.0-alpha1-armhf

This release mirrors PrusaSlicer's upstream 2.2.0-alpha1.

To use this AppImage, dependencies on the host are needed (Raspbian Buster):

apt install -y libboost-dev libboost-regex-dev libboost-filesystem-dev \
libboost-thread-dev libboost-log-dev libboost-locale-dev libcurl4-openssl-dev \
libwxgtk3.0-dev libtbb-dev libcereal-dev libeigen3-dev libnlopt-cxx-dev libudev-dev

After installation, chmod +x PrusaSlicer-2.2.0-alpha1-armhf.AppImage and run it.

PrusaSlicer-2.1.1-armhf

This release mirrors PrusaSlicer's upstream 2.1.1.

To use this AppImage, dependencies on the host are needed (Raspbian Buster):

apt install -y libboost-dev libboost-regex-dev libboost-filesystem-dev \
libboost-thread-dev libboost-log-dev libboost-locale-dev libcurl4-openssl-dev \
libwxgtk3.0-dev libtbb-dev libcereal-dev

After installation, chmod +x PrusaSlicer-2.1.1-armhf.AppImage and run it.

PrusaSlicer-2.1.0-armhf

This release mirrors PrusaSlicer's upstream 2.1.0.

To use this AppImage, dependencies on the host are needed (Raspbian Buster):

apt install -y libboost-dev libboost-regex-dev libboost-filesystem-dev \
libboost-thread-dev libboost-log-dev libboost-locale-dev libcurl4-openssl-dev \
libwxgtk3.0-dev libtbb-dev libcereal-dev

After installation, chmod +x PrusaSlicer-2.1.0-armhf.AppImage and run it.

PrusaSlicer-2.1.0-rc2-armhf

This release mirrors PrusaSlicer's upstream 2.1.0-rc2.

To use this AppImage, dependencies on the host are needed (Raspbian Buster):

apt install -y libboost-dev libboost-regex-dev libboost-filesystem-dev \
libboost-thread-dev libboost-log-dev libboost-locale-dev libcurl4-openssl-dev \
libwxgtk3.0-dev libtbb-dev libcereal-dev
After installation, chmod +x PrusaSlicer-2.1.0-rc2-armhf.AppImage and run it.

PrusaSlicer-2.1.0-rc-armhf.AppImage

This release mirrors PrusaSlicer's upstream 2.1.0-rc.

To use this AppImage, dependencies on the host are needed (Raspbian Buster):

apt install -y libboost-dev libboost-regex-dev libboost-filesystem-dev \ 
libboost-thread-dev libboost-log-dev libboost-locale-dev libcurl4-openssl-dev \ 
libwxgtk3.0-dev libtbb-dev libcereal-dev

After installation, chmod +x PrusaSlicer-2.1.0-rc-armhf.AppImage and run it.

PrusaSlicer-2.1.0-beta3-armhf.AppImage

This release mirrors PrusaSlicer's upstream 2.1.0-beta3.

To use this AppImage, dependencies on the host are needed (Raspbian Buster):

apt install -y libboost-dev libboost-regex-dev libboost-filesystem-dev \ 
libboost-thread-dev libboost-log-dev libboost-locale-dev libcurl4-openssl-dev \ 
libwxgtk3.0-dev libtbb-dev libcereal-dev

After installation, chmod +x PrusaSlicer-2.1.0-beta3-armhf.AppImage and run it.