Unknown command failure with RfSend on sonoff rf bridge v2.2

[rhabacker]

PROBLEM DESCRIPTION

With the latest tasmota development version (version 14.3.0.7 without the portisch firmware) on a sonoff rf bridge v2.2, I can see the RfReceived messages when I press a button on an rf switch, but I cannot use the RfSend command with the appropriate parameters.

According to https://tasmota.github.io/docs/Commands/#rf-transceiver I have tried the examples mentioned there, but they fail (see below)

REQUESTED INFORMATION

Make sure your have performed every step and checked the applicable boxes before submitting your issue. Thank you!

• Read the Contributing Guide and Policy and the Code of Conduct
• Searched the problem in issues
• Searched the problem in discussions
• Searched the problem in the docs
• Searched the problem in the chat
• Device used (e.g., Sonoff Basic): Sonoff Rf Brigde
• Tasmota binary firmware version number used: 14.3.0.7 without the portisch firmware
  • Pre-compiled
  • Self-compiled
• Flashing tools used: ota
• Provide the output of command: Backlog Template; Module; GPIO 255:

  Configuration output here:
22:53:48.540 MQT: stat/tasmota_sonoff/RESULT = {"GPIO0":{"32":"Button1"},"GPIO1":{"3200":"Serial Tx"},"GPIO2":{"0":"None"},"GPIO3":{"3232":"Serial Rx"},"GPIO4":{"0":"None"},"GPIO5":{"0":"None"},"GPIO9":{"0":"None"},"GPIO10":{"0":"None"},"GPIO12":{"0":"None"},"GPIO13":{"320":"Led_i1"},"GPIO14":{"0":"None"},"GPIO15":{"0":"None"},"GPIO16":{"0":"None"},"GPIO17":{"0":"None"}}

• If using rules, provide the output of this command: Backlog Rule1; Rule2; Rule3:

22:54:23.371 MQT: stat/tasmota_sonoff/RESULT = {"Rule1":{"State":"OFF","Once":"OFF","StopOnError":"OFF","Length":0,"Free":511,"Rules":""}}
22:54:23.597 MQT: stat/tasmota_sonoff/RESULT = {"Rule2":{"State":"OFF","Once":"OFF","StopOnError":"OFF","Length":0,"Free":511,"Rules":""}}
22:54:23.847 MQT: stat/tasmota_sonoff/RESULT = {"Rule3":{"State":"OFF","Once":"OFF","StopOnError":"OFF","Length":0,"Free":511,"Rules":""}}

• Provide the output of this command: Status 0:

  STATUS 0 output here:
22:56:29.089 MQT: stat/tasmota_sonoff/STATUS = {"Status":{"Module":25,"DeviceName":"Tasmota","FriendlyName":["Tasmota"],"Topic":"tasmota_sonoff","ButtonTopic":"0","Power":"0","PowerLock":"0","PowerOnState":3,"LedState":1,"LedMask":"FFFF","SaveData":1,"SaveState":1,"SwitchTopic":"0","SwitchMode":[0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0],"ButtonRetain":0,"SwitchRetain":0,"SensorRetain":0,"PowerRetain":0,"InfoRetain":0,"StateRetain":0,"StatusRetain":0}}
22:56:29.097 MQT: stat/tasmota_sonoff/STATUS1 = {"StatusPRM":{"Baudrate":19200,"SerialConfig":"8N1","GroupTopic":"tasmotas","OtaUrl":"http://ota.tasmota.com/tasmota/tasmota.bin.gz","RestartReason":"Software/System restart","Uptime":"0T02:48:56","StartupUTC":"2024-11-29T19:07:33","Sleep":50,"CfgHolder":4617,"BootCount":66,"BCResetTime":"2024-04-24T18:06:21","SaveCount":130,"SaveAddress":"F6000"}}
22:56:29.104 MQT: stat/tasmota_sonoff/STATUS2 = {"StatusFWR":{"Version":"14.3.0.7(038e62b-tasmota)","BuildDateTime":"2024-11-29T16:01:51","Boot":31,"Core":"2_7_8","SDK":"2.2.2-dev(38a443e)","CpuFrequency":80,"Hardware":"ESP8285N08","CR":"380/699"}}
22:56:29.111 MQT: stat/tasmota_sonoff/STATUS3 = {"StatusLOG":{"SerialLog":0,"WebLog":3,"MqttLog":2,"SysLog":1,"LogHost":"","LogPort":514,"SSId":["xxx",""],"TelePeriod":300,"Resolution":"558180C0","SetOption":["00008009","2805C80001000600003C5A0A192800000000","00000080","00006000","00004000","00000000"]}}
22:56:29.125 MQT: stat/tasmota_sonoff/STATUS4 = {"StatusMEM":{"ProgramSize":652,"Free":348,"Heap":22,"ProgramFlashSize":1024,"FlashSize":1024,"FlashChipId":"14325E","FlashFrequency":40,"FlashMode":"DOUT","Features":["0809","8F9AC787","04368001","000000CF","010013C0","C000F981","00004004","00001000","54000020","00000080","00000000"],"Drivers":"1,2,!3,!4,!5,6,7,!8,9,10,12,!16,!18,!19,!20,!21,!22,!24,26,!27,29,!30,!35,!37,!45,62,!68","Sensors":"1,2,3,4,5,6","I2CDriver":"7"}}
22:56:29.133 MQT: stat/tasmota_sonoff/STATUS5 = {"StatusNET":{"Hostname":"tasmota-sonoff-2476","IPAddress":"192.168.x.x","Gateway":"192.168.x.x","Subnetmask":"255.255.255.0","DNSServer1":"192.168.x.x","DNSServer2":"0.0.0.0","Mac":"xx","Webserver":2,"HTTP_API":1,"WifiConfig":4,"WifiPower":17.0}}
22:56:29.140 MQT: stat/tasmota_sonoff/STATUS6 = {"StatusMQT":{"MqttHost":"192.168.x.x","MqttPort":xxx,"MqttClientMask":"DVES_%06X","MqttClient":"DVES_C429AC","MqttUser":"xxx","MqttCount":1,"MAX_PACKET_SIZE":1200,"KEEPALIVE":30,"SOCKET_TIMEOUT":4}}
22:56:29.148 MQT: stat/tasmota_sonoff/STATUS7 = {"StatusTIM":{"UTC":"2024-11-29T21:56:29Z","Local":"2024-11-29T22:56:29","StartDST":"2024-03-31T02:00:00","EndDST":"2024-10-27T03:00:00","Timezone":"+01:00","Sunrise":"08:20","Sunset":"16:56"}}
22:56:29.155 MQT: stat/tasmota_sonoff/STATUS10 = {"StatusSNS":{"Time":"2024-11-29T22:56:29"}}
22:56:29.165 MQT: stat/tasmota_sonoff/STATUS11 = {"StatusSTS":{"Time":"2024-11-29T22:56:29","Uptime":"0T02:48:56","UptimeSec":10136,"Heap":22,"SleepMode":"Dynamic","Sleep":50,"LoadAvg":19,"MqttCount":1,"Wifi":{"AP":1,"SSId":"xxx","BSSId":"xxx","Channel":1,"Mode":"11n","RSSI":88,"Signal":-56,"LinkCount":1,"Downtime":"0T00:00:04"}}}

• Set weblog to 4 and then, when you experience your issue, provide the output of the Console log:

  Console output here:
23:00:03.769 CMD: RfSend 0x7028DC, 24, 1, 10, 238
23:00:03.771 SRC: WebConsole from 192.168.1.99
23:00:03.774 CMD: Grp 0, Cmd 'RFSEND', Idx 1, Len 24, Pld 7350492, Data '0x7028DC, 24, 1, 10, 238'
23:00:03.781 MQT: stat/tasmota_sonoff/RESULT = {"Command":"Unknown","Input":"RFSEND 0x7028DC, 24, 1, 10, 238"}

23:00:40.170 CMD: RfSend {"Data":"0x7028DC","Bits":24,"Protocol":1,"Pulse":238}
23:00:40.172 SRC: WebConsole from 192.168.1.99
23:00:40.175 CMD: Grp 0, Cmd 'RFSEND', Idx 1, Len 54, Pld -99, Data '{"Data":"0x7028DC","Bits":24,"Protocol":1,"Pulse":238}'
23:00:40.182 MQT: stat/tasmota_sonoff/RESULT = {"Command":"Unknown","Input":"RFSEND {\"Data\":\"0x7028DC\",\"Bits\":24,\"Protocol\":1,\"Puls"}

TO REPRODUCE

1. Open the console
2. enter RfSend 0x7028DC, 24, 1, 10, 238 and press return
3. or enter RfSend {"Data":"0x7028DC","Bits":24,"Protocol":1,"Pulse":238}

EXPECTED BEHAVIOUR

The command RfSend should be available and working.

(Please, remember to close the issue when the problem has been addressed)

[sfromis]

No issue here. The RfSend command is only when you have connected a RF transceiver chip directly to the ESP8266. You are instead using RF Bridge, which works differently, and the RfSend command is therefore invalid.
https://tasmota.github.io/docs/Commands/#rf-bridge

[rhabacker]

No issue here. The RfSend command is only when you have connected a RF transceiver chip directly to the ESP8266. You are instead using RF Bridge, which works differently, and the RfSend command is therefore invalid. https://tasmota.github.io/docs/Commands/#rf-bridge

The tasmota documentation for the sonoff rf bridge https://tasmota.github.io/docs/devices/Sonoff-RF-Bridge-433/ states

The Sonoff RF Bridge has two separate chips to handle the Wi-Fi (ESP8285) and RF (EFM8BB1) communications respectively. It is used to send and receive codes with 433.9MHz frequency RF devices.

Doesn't that match?

Codes received from RF devices such as remote controls is passed to the onboard ESP8285 via the serial interface. The code data is relayed via MQTT.

That works

Similarly, the Bridge receives commands over Wi-Fi and sends the encoded data to the RF chip to control an RF device. Thus, the Sonoff RF Bridge "bridges" communications between RF and Wi-Fi.

This means that a transmitter must be included. Which commands are then available for this except RfKey, which does not work as described?

[rhabacker]

Thank you for this clarifying information.

I then tried to save a recognized code with RfKey1 2 and then call it, but this does not work. The device beeps and the red light flashes, but does not respond to the key press that is displayed before the learning process begins. After a while, the learning process is aborted.